Novel,organosoluble, light‐colored fluorinated polyimides based on 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl or 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐1,1′‐binaphthyl

Two series of fluorinated polyimides were prepared from 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl ( 2 ) and 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐1,1′‐binaphthyl ( 4 ) with various aromatic dianhydrides via a conventional, two‐step procedure that included a ring‐opening polyaddition to give poly(amic acid)s, followed by chemical or thermal cyclodehydration. The inherent viscosities of the polyimides ranged from 0.54 to 0.73 and 0.19 to 0.36 dL/g, respectively. All the fluorinated polyimides were soluble in many polar organic solvents, such as N,N‐dimethylacetamide and N‐methylpyrrolidone, and afforded transparent and light‐colored films via solution‐casting. These polyimides showed glass‐transition temperatures in the ranges of 222–280 and 257–351 °C by DSC, softening temperatures in the range of 264–301 °C by thermomechanical analysis, and a decomposition temperature for 10% weight loss above 520 °C both in nitrogen and air atmospheres. The polyimides had low moisture absorptions of 0.23–0.58%, low dielectric constants of 2.84–3.61 at 10 kHz, and an ultraviolet–visible absorption cutoff wavelength at 351–434 nm. Copolyimides derived from the same dianhydrides with an equimolar mixture of 4,4′‐oxydianiline and diamine 2 or 4 were also prepared and characterized. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2416–2431, 2004     

Polyesterification of aromatic dicarboxylic acids and bisphenols with tosyl chloride/dimethylformamide/pyridine promoted by the improvement of the difficult solubility of the activated diacids with lithium chloride

The solution polyesterification of dicarboxylic acids in pyridine, the activated intermediates of which were difficult to dissolve in tosyl chloride/dimethylformamide/pyridine, was investigated in the presence of lithium chloride. The solubility of the activated dicarboxylic acids was largely improved by the presence of the salt, and the polycondensation with bisphenols was greatly facilitated. The salt was more effectively added to a pyridine solution of dicarboxylic acids than to the activated dicarboxylic acids in pyridine. The favorable additive effect on the improved solubility was attributed to a lowered degree of association of the activated dicarboxylic acids, which led to distributions of the resulting oligomers from bisphenols at an earlier stage closer to the theoretical ones and yielded better polycondensation results. The reaction, which proceeded through favorable distributions of the co‐oligomers, produced copolymers of higher inherent viscosities and slightly block sequence distributions determined by NMR. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2725–2733, 2004     

波段三维ESR成像系统的研制（Ⅴ）——灵敏度与分辨率实验及系统总性能指标

实验确定了自行研制的L波段三维电子自旋共振成像（3D-ESRI）系统的检测灵敏度及成像分辨率指标. 用Tempo水溶液模型测量灵敏度结果表明： 样品体积为10 mm, 高30 mm，测量浓度1×10^-4 mol/L水溶液的信噪比为S/N=4∶1；加梯度磁场后，样品浓度需>5×10^-4 mol/L，样品体积为19 mm, 高30 mm时，获得的投影谱的信噪比可满足图像重建的需要. 用DPPH固体样品确定的成像分辨率结果<1 mm. 文中还对ESRI系统的
各项总体性能做了归纳总结.     

X波段六腔渡越管振荡器的高频特性研究

 从麦克斯韦方程出发，采用时域有限差分法（FDTD）和离散傅里叶变换（DFFT）相结合的方法，通过数值计算得出了六腔开放式谐振腔中前四个谐振频率和场分布，计算出的谐振频率与实验测量结果基本相同。比较了开放腔和封闭腔谐振频率，验证了TEM波吸收边界条件，并在实际编程计算中得以应用。计算结果为六腔渡越管振荡器的机理研究提供了依据。     

一种新的永久周期磁铁聚焦的高功率宽带放大器

 提出了一种新的高功率宽带放大器，它由速调管和自由电子脉塞组成，用永久周期磁铁聚焦。研究了这种器件的电子束聚焦、群聚和辐射。在速调管提供一阶调制系数为30%，波导管的半径1.51cm，摇摆器的磁场振幅0.16T，周期7.92cm，电子束的电压490kV，电流50A和半径0.368cm的条件下，预估这种器件的辐射波频率为11.4GHz，输出辐射功率为18MW，输出辐射带宽为44%。     

用于激光推进的高功率激光器的选择

 从激光推进的要求出发，阐述了用于激光推进的高功率激光器的选择原则，即激光器必须满足：（1）高的平均功率和峰值功率；（2）高的单脉冲能量；（3）高的重复频率；（4）优良的大气传输特性。主要分析了目前YAG固体激光器、自由电子激光器和TEA脉冲CO₂激光器的特点，通过上述4个方面性能的比较，认为在目前水平下，TEA脉冲CO₂激光器是进行激光推进的首选强激光源，其优点表现在：功率可达10kW量级，单脉冲能量可达0.5~1kJ，重复频率为20~40Hz；激光波长处于大气传输窗口，对大气变化不敏感；工作物质快速流动，不存在热透镜效应和破坏阈值；相关光学元件易于制造；光束质量较好；运行成本低。     

Determination of residual monomers in acrylate dispersions by gas chromatography

The content of residual monomers is one of the most important characteristics of polymer dispersions. As a result of the similar physicochemical parameters of ethyl acrylate and methyl methacrylate, it is very difficult to determine the residual monomers in acrylate dispersions obtained by emulsion polymerization of both monomers. Gas chromatography with capillary columns, however, permits separation of these monomers and their quantitative determination in acrylate dispersions.     

电站锅炉系统性能仿真模型的建立

1引言根据热力学第二定律，燃料中的化学拥将近一半损失在锅炉的燃烧与传热过程中。因此，优化锅炉性能对降低整个火电机组的煤耗率具有明显效果。完整的锅炉系统由磨煤机、送风机、一次风机、弓讯机、炉膛、汽包、过热器、再热器、省煤器、空气预热器等单元组成，这些单元之间的联结错综复杂。本文建立了锅炉系统中通用单元的性能模型，并在此基础上，对锅炉系统的结构特点进行了分析，利用过程系统工程中的序贯模块法建立了整个锅炉系统的性能模型。对单元的划分、回路的切断及断裂流股的收敛与迭代策略提出了自己的观点。最后根据生产厂…     

Classical versus Jennings model for the ground state of H near a metallic surface

We show that, contrary to earlier reports, application of the one-parameter variational technique to the classical (image) model for H in front of an Al surface leads to energy shifts for the ground state which are very close to those obtained numerically with a more sophisticated model of the system.